转子振动的灰色Verhuslt预测优化控制研究

以灰色预测控制理论为基础，首次将非线性GM模型引入到转子振动主动控制中，并采用现代控制理论中的二次型优化原理，以控制力和响应加权最小为目标函数，设计了转子系统振动的灰色Verhuslt预测优化控制方案。将该方案应用于带电磁阻尼器转子轴承系统的转子振动控制中，仿真结果显示转子振动的灰色预测Verhuslt优化控制是有效的、可行的。     

Principal parametric and three-to-one internal resonances of flexible beams undergoing a large linear motion

A set of nonlinear differential equations is established by using Kane‘s method for the planar oscillation of flexible beams undergoing a large linear motion. In the case of a simply supported slender beam under certain average acceleration of base, the second natural frequency of the beam may approximate the tripled first one so that the condition of 3 : 1 internal resonance of the beam holds true. The method of multiple scales is used to solve directly the nonlinear differential equations and to derive a set of nonlinear modulation equations for the principal parametric resonance of the first mode combined with 3 : 1 internal resonance between the first two modes. Then, the modulation equations are numerically solved to obtain the steady-state response and the stability condition of the beam. The abundant nonlinear dynamic behaviors, such as various types of local bifurcations and chaos that do not appear for linear models, can be observed in the case studies. For a Hopf bifurcation,the 4-dimensional modulation equations are reduced onto the central manifold and the type of Hopf bifurcation is determined. As usual, a limit cycle may undergo a series of period-doubling bifurcations and become a chaotic oscillation at last.     

Effect of parameters on the rubbing condition of an unbalanced rotor system with initial permanent deflection

A rotor-stator rubbing Jeffcott model of a rotor system with mass unbalance including the mass eccentricity and the initial permanent deflection was set up and the corresponding governing motion equation was derived by d’Alembert principle. Through the analytical method, the rubbing condition was analyzed. Whether the rub would happen and when the rub would happen were well solved. The amplitude of the rotor center was calculated, and the rubbing factor was introduced to determine whether the rub would happen or not for all rotating speeds. Rubbing speeds when rub began to happen were obtained. Parameters such as the mass eccentricity, the initial permanent deflection, damping coefficients, and the phase angle between the mass eccentricity and the permanent deflection were used to analyze their effect on the rubbing condition. Results were obtained and could be used to prevent the rubbing fault or decrease the damage of the rub and diagnose or balance the initial permanent deflection fault.     

DYNAMICS ANALYSIS OF STOCHASTIC SPATIAL FLEXIBLE MULTIBODY SYSTEM 1)

轻质、高精度的柔性多体系统被广泛应用于实际工程领域中.由于实际设计公差、制造误差及环境温度等多种不确定因素的存在,使得柔性多体系统的结构参数(物理参数和几何参数)表现出随机性.具有随机结构参数的动力学模型能够客观地反映出真实系统的动力学行为,且结构参数的不确定性对空间柔性多体系统动力学响应的影响是不容忽视的.针对具有多个随机参数的空间柔性多体系统,提出了一种基于广义alpha算法的非侵入式随机柔性多体系统动力学计算方法.采用绝对节点坐标公式(absolute node coordinate formulation, ANCF)来描述柔性体, 推导建立多体系统动力学模型.利用混沌多项式展开(polynomial chaos expansion, PCE)法构建系统随机动力学方程的代理模型,然后将随机响应面法(stochastic response surface method, SRSM)嵌入广义-alpha方法中,分别采用改进抽样的回归方法(regression method of improved sampling, RMIS)和单项求容积法则(Monte Carlo simulation, MCR)来确定样本点.将数值计算结果与蒙特卡洛模拟(Monte Carlo simulation, MCS)结果进行对比, 验证了所提算法的有效性.在相同的定积分精度的条件下,根据单项求容积法则确定的样本点的计算结果稳定性更强, 且其计算效率更高.     

柔性系统力学中的主要课题

本文对多刚体系统力学的研究结果进行简要的小结,介绍了柔性系统的力学模型以及该领域中的主要研究课题.     

挤压油膜阻尼器-滑动轴承-柔性转子系统的动力响应分析

建立了挤压油膜阻尼器-滑动轴承-柔性转子非线性系统的动力学模型,采用Runge-Kutta法进行求解,进而对系统的稳定性和分叉行为进行了研究。仿真计算结果表明,系统能够在一定范围内保持稳定,随着转速的变化系统将会出现倍周期、准周期及混沌响应,从而为有效地控制转子的稳定运行状态提供了理论依据。     

刚柔耦合建模理论的实验验证

传统的混合坐标建模理论是零次近似方法，对刚柔耦合问题的描述存在缺陷，研究以一个由中心刚体，柔性梁及末端质量组成的刚柔耦合系统对象，建立了精确的一次近似的刚柔耦合动力学方程，在该模型中计及了结构阻尼及风阻的影响，利用单轴气浮台动力学实验平台，通过与实验数据的比较，说明了传统零次近似方法在某些条件下已不能下确描述柔性的刚性正确性和可靠性。     

AN EXACT METHOD OF BENDING OF ELASTIC THIN PLATES WITH ARBITRARY SHAPE

ＡＮ　ＥＸＡＣＴ　ＭＥＴＨＯＤ　ＯＦ　ＢＥＮＤＩＮＧ　ＯＦ　ＥＬＡＳＴＩＣ　ＴＨＩＮ　ＰＬＡＴＥＳ　ＷＩＴＨ　ＡＲＢＩＴＲＡＲＹ　ＳＨＡＰＥＺｈｏｕＤｉｎｇ（周叮）（ＲｅｃｅｉｖｅｄＡｐｒｉｌ１０，１９９５，ＲｅｖｉｓｅｄＡｐｒｉｌ２６．１９９６．Ｃ...     

汽轮机转子的温度场及热应力场计算

利用积分变换法导出了蒸汽温升率连续变化时汽轮机转子的温度场和热应力场计算公式。本公式可直接应用于转子的应力监测与控制。和差分法相比，解析法的数据处理速度快，能满足快速监测、及时跟踪与控制的要求。关键词：汽轮机转子；温度场；热应力场     

非惯性系下柔性悬臂梁的振动主动控制

采用变结构控制方法对非惯性系下柔性悬臂梁的振动主动控制进行研究．重点通过算例揭示一次近似模型与传统的零次近似模型的巨大差异，以及变结构方法在控制非惯性系下柔性悬臂梁的稳态振动的有效性．结果表明，当大范围旋转运动角速度较大时，传统零次近似模型不能对动力系统进行正确的数学描述；变结构控制方法能够使得非惯性系下梁的稳态振动得到完全镇定，且该方法对转动角速度变化具有较好的鲁棒性；采用零次近似模型进行控制设计的控制效果将在某一临界角速度条件下出现失效，该临界角速度值大于静止悬臂梁的基频．